Chip 1997 March/CHIP Mart 1997.iso/SurfCam/SURFCAM.Z/IGS2DSN.CFG

Text File | 1996-04-01 | 15KB | 310 lines

#begin default section
begin default

Units               Inches     Units for the numbers below


Tolerance           0.00005    Default tolerance for trims & breaks
ChainTol            0.001      Default tolerance for chain selection
ViewTol             0.1        Default angular degrees to find "existing" views
SurfIntTol          0.0004     Default Surface Intersection Tolerance
ProjectTol          0.0004     Default Projection tolerance
DiscontTol          0.0002     Default tolerance for spline continuity
PolylineTol         0.001      Default tolerance for polyline continuity
ConvertBoundedPlane 1          Convert bounded planes to trim surfaces
MaxPlaneDistance    10000.0    Distance beyond which Planes are ignored
DefaultPlaneSize    1.0        Size of square  planes are brought in as
FixDegenerateSurf   1          Fix degenerate surfaces
DegenerateTrimSize  0.0004     Distance to trim degenerate surfaces back by
ResizePlanarSurf    1          Resize planar surfaces ?
MaxPlanarSurfSize   1          Surfaces bigger than this will be resized
OffsetSurfFactor    3          Density of surface offset
ExtendPlane         .1         Distance to extend the trimmed planar surface
DisplayU            5          Default number of display lines in U
DisplayV            5          Default number of display lines in V

ConvertToNURB       0          1 Convert parametric surfaces to NURBS
                               0 Do not convert parametric surfaces to NURBS
ConvertClosed114ToNURB    1    1 Convert closed parametric surfaces to NURBS
                               0 Do not convert closed parametric surfaces to NURBS

CheckDependencies   0          1 -- Verify dependencies are set correctly and
                                    fix them if they are not.
                               0 -- Assume IGES file dependencies are set
                                    correctly and bring in multiple instances

ProcessUncalledItems 1         1 -- Bring in unprocessed items also
                               0 -- If checking dependencies do not bring in
                                    items for which we do not have parent items

TrimOption          4          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces

Degree1NURB         1          1 -- Handle degree 1 NURB curves as polylines for trimming
                               0 -- Handle degree 1 NURB curves as regular NURB curves

RevTabcylUV         0          1 -- UV boundaries ok for Rev Surf's and Tabulated Cylinders
                               0 -- UV boundaries not ok for Rev Surf's and Tabulated Cylinders

#end of default values
end default


#system dependent options

begin System_Id "SURFCAM"
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
end

begin System_Id "ANVIL-5000"
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
end

begin System_Id "Autocad"
ResizePlanarSurf    0          Resize planar surfaces ?
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces


Degree1NURB         1          1 -- Handle degree 1 NURB curves as polylines for trimming
                               0 -- Handle degree 1 NURB curves as regular NURB curves

ConvertToNURB       1          1 Convert parametric surfaces to NURBS
                               0 Do not convert parametric surfaces to NURBS
end

begin System_Id "CADDS"
RevTabcylUV         1          1 -- UV boundaries ok for Rev Surf's and Tabulated Cylinders
                               0 -- UV boundaries not ok for Rev Surf's and Tabulated Cylinders
end

begin System_Id "CAMAX"
TrimOption          4          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
RevTabcylUV         1          1 -- UV boundaries ok for Rev Surf's and Tabulated Cylinders
                               0 -- UV boundaries not ok for Rev Surf's and Tabulated Cylinders
end

begin System_Id "CATIA"
CheckDependencies   1          1 -- Verify dependencies are set correctly and
                                    fix them if they are not.
                               0 -- Assume IGES file dependencies are set
                                    correctly and bring in multiple instances
ProcessUncalledItems 1         1 -- Bring in unprocessed items also
                               0 -- If checking dependencies do not bring in
                                    items for which we do not have parent items
PolylineTol         0.0014     Default tolerance for polyline continuity
TrimOption          4          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
end

begin System_Id "CGS"
GroupToLayers       1          0 -- Do not make a layer for every group
                               1 -- Make a layer for every group
TrimOption          5          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
end

begin System_Id "CLEAR CUT"
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
end

begin System_Id "DUCT"
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
end

begin System_Id "HP Precision Engineering"
TrimOption          1          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
RevTabcylUV         1          1 -- UV boundaries ok for Rev Surf's and Tabulated Cylinders
                               0 -- UV boundaries not ok for Rev Surf's and Tabulated Cylinders
Degree1NURB         0          1 -- Handle degree 1 NURB curves as polylines for trimming
                               0 -- Handle degree 1 NURB curves as regular NURB curves
end

begin System_Id "HP PE"
TrimOption          1          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces

RevTabcylUV         1          1 -- UV boundaries ok for Rev Surf's and Tabulated Cylinders
                               0 -- UV boundaries not ok for Rev Surf's and Tabulated Cylinders
Degree1NURB         0          1 -- Handle degree 1 NURB curves as polylines for trimming
                               0 -- Handle degree 1 NURB curves as regular NURB curves
end

begin System_Id "Intergraph"
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces

Degree1NURB         0          1 -- Handle degree 1 NURB curves as polylines for trimming
                               0 -- Handle degree 1 NURB curves as regular NURB curves


RevTabcylUV         1          1 -- UV boundaries ok for Rev Surf's and Tabulated Cylinders
                               0 -- UV boundaries not ok for Rev Surf's and Tabulated Cylinders

end

begin System_Id "Iris"
TrimOption          2          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces

end

begin System_Id "MASTERCAM"
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces
end

begin System_Id "Microstation"
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces

Degree1NURB         0          1 -- Handle degree 1 NURB curves as polylines for trimming
                               0 -- Handle degree 1 NURB curves as regular NURB curves
end

begin System_Id "Pro/Engineer"
TrimOption          4          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces

RevTabcylUV         0          1 -- UV boundaries ok for Rev Surf's and Tabulated Cylinders
                               0 -- UV boundaries not ok for Rev Surf's and Tabulated Cylinders

end

begin System_Id "SolidWorks"
ResizePlanarSurf    0          Resize planar surfaces ?
TrimOption          3          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces

RevTabcylUV         1          1 -- UV boundaries ok for Rev Surf's and Tabulated Cylinders
                               0 -- UV boundaries not ok for Rev Surf's and Tabulated Cylinders

end

begin System_Id "Unigraphics"
ProjectTol          0.0040     Default Projection tolerance
TrimOption          2          0 -- Use preference flag but favor XYZ
                               1 -- Use preference flag but favor UV
                               2 -- Use XYZ
                               3 -- Use UV
                               4 -- Use preference flag but favor XYZ
                                    except for closed & degenerate surfaces
                               5 -- Use XYZ except for closed & degenerate surfaces

end

begin System_Id "Visicad"
Degree1NURB         0          1 -- Handle degree 1 NURB curves as polylines for trimming
                               0 -- Handle degree 1 NURB curves as regular NURB curves

end

begin System_Id "SDRC"
end

begin System_Id "STRIM/100"
end

begin System_Id "Autodesk"
end

begin System_Id "CADKEY"
end

begin System_Id "CIMLINC"
end

begin System_Id "PDGS"
end